Call Us 800.362.8774 Call Us 866-294-5847 Contact Training Training Training WeatherTRAK Login WaterCompass Login AppManager Login

Thank you!

    Krista McAllester
    kmcallester@hydropoint.com

    Krista activity

    0 Articles Written Last Month

    0 0 0 0 0 0 0

    Updated December 13th, 2023 by Krista McAllester

    How to Wire a Single or Two Valve Decoder

    Single Valve (WT2W-H20-1VD) and Two Valve (WT2W-H20-1VD) Note If the master valve decoder is not pre-programmed you will need to program it at the controller BEFORE wiring. For instructions on how to program a decoder read: Programming a Single Valve Decoder and Programming a Two Valve Decoder   Warning The Decoder wires must not have electrical con...

    1 min reading time
    Updated October 23rd, 2024 by Krista McAllester

    (OFL) Controller Offline

                                                                                                  When a controller offline alert occurs, it means that the controller has not had recent communication with the WeatherTRAK Central server. Unless the power is off, the controller will continue to irrigate as scheduled; however, the controller may not receiv...

    2 min reading time
    Updated April 1st, 2024 by Krista McAllester

    OptiFlow Key Terms

    OptiFlow is the elite software on WeatherTRAK that combines the features from the traditional WeatherTRAK system with additional flow management tools in the cloud. Hardware OptiFlow XR: This controller is compatible with all OptiFlow features in any OptiFlow compatible scenario.  Upgraded Pro3: This is a WeatherTRAK controller that has replaced its...

    6 min reading time
    Updated July 25th, 2024 by Krista McAllester

    Command Panel Replacement

    Command Panel Replacement Power down the controller. Unplug the old command panel  Plug in new command panel.  Ensure the ribbon cable is connected on both ends Ensure the Cloud / Optiflow key is installed Resecure panel Power up the controller and validate screen is visible if the contrast needs to be adjusted, press Setup > press Up or Down Arr...

    0 min reading time
    Updated December 12th, 2023 by Krista McAllester

    Flow HD Installation

    For Plastic FlowHD use this Installation manual. For the Iron FlowHD use this Installation manual. Important: Make sure to install FlowHD in correct pipe location/ flow direction. Example  ...

    0 min reading time
    Updated June 3rd, 2024 by Krista McAllester

    Signal Test Kit for Site Survey

    LTE Signal Test Kit is a network scanner used to identify which bands and carriers on available on the site. Band availability depends on nearest cell tower, topography, etc.  This helps Customers: measure the local signal strength (RSRP) and quality (RSRQ) to ensure signal meets system connection requirements identify strongest and best carrier and...

    0 min reading time
    Updated December 12th, 2024 by Krista McAllester

    Control Point & Dynamic Flow Allocation Groups

    There are two different, but very similar, features for turning on the smallest available control points. Control Point Groups can only be used with a FlowStation. Only use control point groups for configurations with a shared water source. An example use case for a control point group configuration is if the customer doesn’t want their control poin...

    0 min reading time
    Updated September 5th, 2024 by Krista McAllester

    Instructions for Accessing the HPDS ETE Data Service

    Via command line Secure FTP client (PSFTP used in example) Open your Secure File Transfer Protocol (SFTP) client application. Open a session to ftp.wtdata.com : Double click executable to launch. At the command prompt “psftp>” type “open ftp.wtdata.com ”. At prompt “login as:” type your assigned username and press enter. At prompt username @ftp.w...

    0 min reading time
    Updated April 25th, 2024 by Krista McAllester

    Incorrect Flow Data

    There have been instances when a flow sensor is detecting higher flow than expected, such as detecting flow when watering is unscheduled or the master valve is shut off. So far, these  'phantom flow'  events have only occurred with controllers connected to  Flow HD Plastic ultrasonic  flow  sensors. Although there are many environmental factors that...

    2 min reading time
    Updated August 27th, 2024 by Krista McAllester

    Flow3 Installation

    Flow3 Product Documents New Solenoid Design As of August 2024, Flow3 meters will have a new solenoid design. Installation will remain the same, but instead of two black wires, there is now a brown and blue. Neither are polarized, so wires can be connected to either terminal. One major change is the switch to change the solenoid from open to automati...

    0 min reading time
    Updated December 7th, 2023 by Krista McAllester

    Cellular Communication (LTE) Antenna Tips

      For Cellular Communication Antennas For Directions on installing the Omni Outdoor Cylinder Antenna go Omni Directional Antenna_Installation Guide When using an external antenna, placement of that antenna is critical to a solid data link. The key to the overall robustness of the communication link is the height and placement of the antenna. In gene...

    0 min reading time
    Updated August 30th, 2024 by Krista McAllester

    Chassis Replacement

       ...

    0 min reading time
    Updated December 22nd, 2023 by Krista McAllester

    FlowHD Iron - Battery Replacement

    To replace the battery in the iron FlowHD, please follow the instructions below. HydroPoint is not responsible for purchasing battery nor the associated repair material nor obligated to perform the repair. Battery Replacements will void both HydroPoint's and Netafim's Manufacturing Warranties. Replacements should only be done with meters that are ou...

    0 min reading time
    Load More