Source: Tempo Communications Webinar
Presenter: Alejandro Asencio, Associate Product Manager - Irrigation

Two-Wire System Overview

What is Two-Wire?

Two-wire irrigation systems require only two wires from the controller to operate many valves in the field, as opposed to conventional systems that require one wire per valve plus a common.

Key Characteristics:

Significantly reduces wire requirements for large systems

Uses decoders as intermediaries between controller and valves

The two wires must always be kept separate and not touching

Different colored wires recommended for tracking

Many systems have constant voltage for two-way communication between controller and decoders

When Two-Wire Makes Financial Sense

Break-even point: Approximately 30-40 valves

Optimal for: Systems with many valves (can operate hundreds on one wire path)

Long-distance capability: Can operate valves across much larger distances.

Expansion advantage: Add zones by extending wire path, not running new wires back to controller

Two-Wire vs. Conventional Wiring

Conventional System:

One wire per valve from controller

Wire bundle grows with each valve

Expansion requires running wire back to controller

Simpler troubleshooting (isolated circuits)

Two-Wire System:

Two wires total for entire wire path

Can operate hundreds of valves

Easy expansion (add to end of wire path)

Requires decoders

More complex troubleshooting (shared circuit)

System Components

1. Controller

Sends voltage and digital communication signals

Provides diagnostics and error messages

May have "short finding mode" or "wire test mode"

Can communicate with decoders bidirectionally (on two-wire/non-conventional systems)

2. Two-Wire Path

30 VAC RMS over two-wire

Supports up to 1.45 amp output

Must use proper two-wire cable (separate colors recommended)

Runs throughout the site connecting all valve boxes

Can be configured as:

Branched/Star pattern (recommended for troubleshooting)

Loop pattern (adds redundancy but harder to troubleshoot)

For more two-wire details see Baseline Two-wire Technical Specification

3. Valves and Solenoids

Standard irrigation valves with solenoids

Solenoid resistance should measure 20-60 ohms

Connected to decoder via two wires

4. Splices

Each valve box contains minimum of 4 waterproof splices:

Two splices connecting decoder to two-wire path

Two splices connecting decoder to solenoid

5. Grounding System

Grounding plates or rods placed periodically along wire path

Surge arrestors at each grounding point

Protects system from lightning damage

Critical because entire system is one linked circuit

For more grounding details see Baseline Surge Arrestor & Grounding Specification

Common Failure Points

Primary Causes of Failure (in order of frequency):

Bad Splices (Most Common)

Compromised waterproofing

Corrosion in connections

Water intrusion leading to decoder failure

Failed Decoders

Usually caused by water intrusion from poor splices

Constant voltage attracts water into exposed connections

Electricity + water = accelerated corrosion

Damaged Wire Insulation

Nicking inner conductors during jacket stripping

Cable damage from digging or landscaping

Repeated thermal expansion/contraction stressing nicked wires

Why Splices Are Critical

Systems with two-way communication are especially vulnerable because:

Constant voltage on the wire path

Electricity literally attracts moisture into exposed connections

Heating/cooling cycles from valve operation create stress

Small imperfections become major failures over time

Proper Splicing - DBRY6 Waterproof Splices

Correct Installation:

Wires must be undamaged (no nicked copper)

Don't overtighten wire twist

Waterproof gel must be pushed away from tube end

Creates protective gel layer from connection to tube opening

Wire nut must be fully inserted into tube

Inadequate Methods (DO NOT USE on two-way communication systems):

Gel-filled wire nuts alone (insufficient protection)

Standard wire nuts with electrical tape

Any non-waterproof connection method

Additional Resources

Recommended: Noe Cruz YouTube video on splicing methodology

20-minute detailed video

Claims 100% success rate with his method

May differ from standard industry methods

Extensive field experience

The Milliamp Clamp Meter Tool

Why a Milliamp Clamp Meter is Essential

Primary Advantage: Non-invasive troubleshooting

No need to break connections

Preserves existing splices

Saves time and materials

Prevents introducing new problems

Without a Milliamp Clamp Meter:

Must physically break wire path in half

Test each section separately

Replace splices each time ($$ and time)

Risk creating new problems with new splices

Walk back and forth to controller repeatedly

ROI: Tool pays for itself quickly through time and materials saved

How It Works

Measures outgoing current on the two-wire path to determine what's happening downstream:

Good decoders: 0.5 - 1.5 milliamps idle (consistent per model)

Failed decoder/short: Much higher current draw

Disconnected decoders: Lower current than expected

Understanding Waveforms

Standard AC Power:

60Hz in USA, 50Hz in other countries

Smooth sine wave

Easy for most meters to read. True RMS handles any waveform accurately

Two-Way Communication:

Rapid bursts of data superimposed on main voltage

Can interfere with measurements

Low Pass Filter eliminates these bursts from readings

Electrical Fundamentals

Ohm's Law Review

V = I × R

Where:

V (Voltage): Electrical pressure (like water pressure from pump)

I (Current): Flow rate of electricity (what clamp meter measures)

R (Resistance): Restriction to flow

Key Principle: With constant voltage from controller:

Lower resistance = Higher current (overcurrent/short)

Higher resistance = Lower current (normal operation)

Very high resistance = No current (open circuit/disconnect)

Water System Analogy

Think of two-wire system as water main and sewer line serving houses on a street:

Components:

Water main: One wire supplying power

Sewer line: Other wire returning power

Houses: Decoders consuming water/electricity

Leaky toilet: Bad decoder (constant high usage)

Burst water main: Short circuit (massive flow)

Broken fire hydrant: Ground fault (water/current leaking to earth)

Closed valve: Open circuit (no flow to houses downstream)

Why This Analogy Works:

Current flows out on one wire, returns on the other

Clamping both wires = average of flow in/out = zero reading

Must clamp only one wire at a time

Upstream has more total flow than downstream

Can identify problem location by where flow changes

Troubleshooting Process

Step 1: Controller Diagnostics

Is the controller turning on?

If NO, check:

Power switch position

Blown fuses

Supply voltage to transformer (should be 120V AC in USA)

Transformer output voltage (should be 24V AC typically)

Connections and wiring

If controller won't turn on WITH wire paths connected:

Disconnect all wire paths from controller

If controller now turns on: Overcurrent condition exists

If controller still won't turn on: Controller problem

If YES, review controller information:

Overcurrent errors?

Specific zone offline messages (zones 18-23 offline)?

Current usage readings?

Diagnostic error codes?

Step 2: Identify Wire Path Configuration

Break any loops before troubleshooting:

Loop systems: Wire path forms complete circle

Makes "upstream vs. downstream" ambiguous

Break connections at furthest points of loops

Converts system to star/branched pattern

Enables clear upstream/downstream measurements

Document your system:

Create or reference system map

Know where valve boxes are located

Understand branching patterns

Mark wire path colors if available

Step 3: Isolate Problem Wire Path

If multiple wire paths exist:

Disconnect wire paths one at a time from controller

Check if error clears with each disconnection

When error clears, you've identified problem path

Reconnect to verify error returns

Focus troubleshooting on that wire path only

Step 4: Determine Problem Type

Three Main Problem Categories:

A. Overcurrent (Short/Ground Fault)

Controller shows overcurrent error or enters short finding mode

High current readings on milliamp clamp meter

Most common problem requiring clamp meter

B. Open Circuit (Disconnection)

Specific zones offline

Lower than expected current readings

May affect multiple consecutive zones

C. Individual Device Problems

Specific zone errors

May only occur when zone operates

Often solenoid-side of decoder

Step 5: Resistance Testing (if needed)

Test 1: Wire-to-Wire Resistance

Disconnect two-wire path from controller

Measure resistance between the two wires

Expected: Very high resistance (>600kΩ or "OL" for overload)

Problem if: Low resistance indicates short

Test 2: Wire-to-Ground Resistance

Measure between each wire and ground lug at controller

Ground lug should have continuity to earth

Expected: Very high resistance (>600kΩ or "OL")

Problem if: Low resistance indicates ground fault

Test 3: Wire Continuity (Shorted End Test)

Short the two wires together at furthest point

Measure resistance between wires at controller

Expected for 14-gauge: 2.5 ohms × 2 × (distance in thousands of feet)

Example: 1,000 feet of 14-gauge = 5 ohms total

Expected for 12-gauge: 1.6 ohms × 2 × (distance in thousands of feet)

Problem if: Much higher = bad splice/corrosion in path

Test 4: Solenoid Resistance

Measure across solenoid wires

Expected: 20-60 ohms

Problem if: Outside this range (open or shorted solenoid)

Step 6: Current Testing Setup

If controller has short finding/wire test mode:

Use this mode for testing

Provides steady current for measurements

May display current draw digitally

If controller is damaged or won't provide test mode:

Create External Power Supply:

Components needed:

Transformer rated for minimum 25 volt-amps or 1 amp current

Standard irrigation solenoid

Wire connectors

Assembly:

Connect transformer to power

Splice solenoid into ONE wire only from transformer

Connect other wire directly from transformer to wire path

Solenoid limits current to safe 200-300mA range

Prevents transformer burnout and decoder damage

Alternative if controller shuts down but isn't damaged:

Splice solenoid into one wire at controller output

Adds enough resistance for controller to operate safely in test mode

Safety Warning: Never connect transformer directly to wire path without solenoid current limiter. Can cause:

Transformer burnout

Tripped breakers

Overheated/melted/ignited decoders

System damage

Measurement Techniques

Using the Milliamp Clamp Meter

Setup:

Set meter to milliamps (first position on dial)

If measuring idle system with communication, hold HOLD button for 2 seconds to engage Low Pass Filter (LPF will appear on display)

Clamp around only ONE wire at a time

Wait 2-3 seconds for steady reading

Critical Rule: Clamp Only One Wire

Why:

Current flows opposite directions on the two wires

Clamping both = average of both = zero (false reading)

Must measure each wire individually

Exception: Clamping both wires can detect imbalance from ground fault on single wire, but not useful for most troubleshooting.

Interpreting Current Readings

Current Math:

Total current = Number of decoders × Current per decoder

Example: 28 decoders × 1.4mA each = 39.2mA total

Measurement Locations:

At controller: 100% of system current

Halfway down path: 50% of system current

At decoder: Only that decoder's current

Reading Analysis:

Higher than expected: Short, ground fault, or bad decoder downstream

Lower than expected: Open circuit, disconnected decoders, or problem upstream

Normal at one point, abnormal at next: Problem is between those two points

The Binary Search Method

Most efficient troubleshooting approach:

Start at controller: Measure current, confirm problem exists

Check both wires: Ensure you're not missing ground fault on single wire

Go halfway: Measure at midpoint of wire path

Still high? Problem is in downstream half

Now normal? Problem is in upstream half

Go halfway again: Measure at midpoint of problem section

Repeat: Continue dividing problem section in half

Pinpoint: When you find where reading changes, problem is at that location

At Branch Points:

Measure at beginning of each branch

Identifies which branch contains problem

Significantly narrows search area

Strategic Measurement Points

Priority locations:

At controller (baseline measurement)

At branch junctions (isolate which branch)

At valve boxes (most likely failure points)

Between valve boxes (only if indicated)

Remember: Problems are most likely at:

Splices in valve boxes

Wire damage during stripping

Decoder connections

Baseline Documentation

For healthy systems:

Record total current at controller for each wire path

Record current at major branch points

Document decoder count for each section

Note decoder model and expected draw per decoder

Save for future comparison

Example Scenarios

Scenario 1: Overcurrent Condition

System Details:

10 decoders total

Each decoder uses 2.5mA idle

Expected total: 10 × 2.5 = 25mA

Symptoms:

Controller shows overcurrent error

System won't operate normally

Step 1: Initial Measurement

Measure at controller

Reading: 80mA (should be 25mA)

Problem confirmed: Overcurrent condition

Step 2: Check Both Wires

Red wire: 80mA

Blue wire: 80mA

Conclusion: Short circuit (not ground fault on single wire)

Step 3: Go Halfway

Measure at midpoint (5 decoders upstream, 5 downstream)

Reading: 12.5mA (5 × 2.5 = expected)

Conclusion: Problem is UPSTREAM (in first half)

Step 4: Check First Half Branches

Branch A (2 decoders): 5mA (2 × 2.5 = normal)

Branch B (3 decoders): 75mA (should be 7.5mA)

Conclusion: Problem is in Branch B

Step 5: Narrow Down Branch B

Measure at first valve box in Branch B

Reading: 75mA (high)

This is the problem location

Step 6: Verify Decoder vs. Splice Problem

Clamp around wire coming off two-wire path to this specific decoder

Reading: 72.5mA (should be 2.5mA)

Conclusion: This decoder is the problem (not the splices to wire path)

Step 7: Resolution

Remove and replace failed decoder

Test removed decoder at controller (should confirm failure)

Measure again after replacement

Verify normal readings throughout system

Total measurements: 7 measurement points to identify exact problem

Without clamp meter: Would have required breaking multiple splices, testing sections, replacing splices, walking to controller repeatedly.

Scenario 2: Ground Fault (Single Wire)

Symptoms:

Overcurrent condition

Affects entire wire path

Measurements:

Red wire at controller: 80mA (high)

Blue wire at controller: 25mA (normal)

Conclusion: Ground fault on red wire only

Finding the Fault:

Use binary search on RED wire only

Find where high current drops to normal

Problem is at that location (likely bad splice or nicked wire)

Alternative: If fault is between valve boxes, use P-203 Ground Fault Locator:

Isolate section of cable (disconnect from decoders and controller)

Clip locator transmitter to BOTH wires (ensures detection regardless of which wire is faulted)

Walk wire path with receiver

Locate exact point of ground fault

Scenario 3: Open Circuit

System Details:

28 decoders expected

Each uses 1.4mA

Expected total: 28 × 1.4 = 39.2mA

Symptoms:

Controller reports zones 18-23 offline

Multiple consecutive zones not working

Step 1: Initial Measurement

Reading at controller: 31.5mA (should be 39.2mA)

Missing: 39.2 - 31.5 = 7.7mA

Calculation: 7.7 ÷ 1.4 = 5.5 decoders

Conclusion: Approximately 6 decoders offline (matches zones 18-23)

Step 2: Use Controller Information

Zones 18-23 are reported offline

Navigate to those zones in the field

Measure current before first offline zone

Step 3: Confirm Break Point

Measure at zone 17: 31.5mA (matches controller reading)

Measure at zone 18: 0mA

Conclusion: Break is between zone 17 and zone 18

Step 4: Inspect Connection

Open valve box between zones 17 and 18

Likely finds:

Disconnected splice

Severely corroded connection

Cut wire

Lightning-damaged section

Step 5: Resolution

Repair or replace connection

Verify current returns to normal (39.2mA)

Test all zones 18-23 for proper operation

Scenario 4: Solenoid-Side Problem

Symptoms:

Overcurrent ONLY when specific zone operates

No overcurrent when system is idle

Analysis:

Problem is on SOLENOID side of decoder, not two-wire path

Short in solenoid circuit only draws current when zone activates

Possible Causes:

Shorted solenoid (resistance too low)

Bad splices between decoder and solenoid

Damaged wire between decoder and valve

Troubleshooting:

Measure solenoid resistance (should be 20-60 ohms)

Inspect decoder-to-solenoid splices

Check decoder solenoid output connections

Test with known good solenoid if available

Scenario 5: Multiple Branches

System Configuration:

Wire path splits into 3 branches at junction

Branch A: 8 decoders

Branch B: 12 decoders

Branch C: 6 decoders

Each decoder: 1.5mA

Expected readings:

Total at controller: 26 × 1.5 = 39mA

Branch A only: 8 × 1.5 = 12mA

Branch B only: 12 × 1.5 = 18mA

Branch C only: 6 × 1.5 = 9mA

Symptoms:

Reading at controller: 68mA (overcurrent)

Step 1: Measure Each Branch

At junction before Branch A: 12mA (normal)

At junction before Branch B: 47mA (high - should be 18mA)

At junction before Branch C: 9mA (normal)

Conclusion: Problem is in Branch B

Step 2: Apply Binary Search to Branch B

Continue halving Branch B until problem found

Efficiency: Eliminated 14 decoders (A and C) from investigation with 3 measurements

Troubleshooting Quick Reference

Problem Type Identification

Measurement Interpretation

Binary Search Process

Measure at controller → Confirm problem and type

Check both wires → Identify if ground fault is on one wire

Measure at halfway point → Determine which half contains problem

Measure at quarter point → Further narrow problem section

Continue halving → Until problem isolated to single valve box

Verify specific component → Decoder, splice, or wire

FAQ

Why must I use a milliamp clamp meter? Can't I use a regular amp meter?

Standard amp meters (clamp or multimeter) typically have minimum ranges of 0-10 amps or 0-100 amps. Decoders use 0.5-5 milliamps (0.0005 to 0.005 amps). A standard amp meter cannot accurately measure such small currents. You need a specialized milliamp clamp meter that reads down to 0.001 amps.

What is True RMS and why does it matter?

True RMS (Root Mean Square) accurately measures any waveform shape. Many two-wire systems use non-standard waveforms (square waves, slow frequencies, communication bursts). Standard meters assume a smooth sine wave and will give inaccurate readings on unusual waveforms. True RMS calculates the actual effective current regardless of wave shape.

What is the Low Pass Filter and when should I use it?

The Low Pass Filter (LPF) filters out high-frequency signals above 160Hz. Two-way communication creates rapid bursts of data that can make readings unstable. Engaging LPF ignores these bursts while measuring the steady idle current from decoders. Use LPF when measuring idle systems with two-way communication. Starting soon, it will be enabled by default on CMA-360B.

Why do I get zero reading when clamping both wires?

Current flows in opposite directions on the two wires (out on one, back on the other). The clamp meter averages the magnetic fields from both conductors. Equal and opposite currents cancel out, giving zero. You must clamp only one wire at a time to get an accurate reading.

Can I troubleshoot two-wire systems without a milliamp clamp meter?

Yes, but it's much more time-consuming and expensive:

Must physically break wire path connections

Test sections individually

Replace splices each time (cost)

Walk back to controller repeatedly

Risk creating new problems with new splices

A $200 milliamp clamp meter pays for itself quickly

What if my controller won't provide power due to overcurrent?

Option 1: Some controllers have "short finding mode" or "wire test mode" that provides limited current for testing despite overcurrent condition.

Option 2: Splice a solenoid into one wire at the controller to add resistance, allowing controller to operate safely.

Option 3: Create external power supply:

Transformer (25VA or 1A minimum rating)

Solenoid spliced into ONE wire only (limits current to safe 200-300mA)

Connect to wire path for testing

How do I know how much current each decoder should draw?

Method 1: Check manufacturer specifications:

0.5-1.5mA (Excluding flow biCoders)

Method 2: Measure a known healthy system with same equipment

Method 3: Calculate from total:

Measure total current at controller

Divide by number of decoders

Example: 39.2mA ÷ 28 decoders = 1.4mA per decoder

Why are splices so critical in two-wire systems?

Systems with two-way communication have constant voltage on the wire path. Electricity combined with moisture:

Attracts water into exposed connections

Dramatically accelerates corrosion

Creates decoder failures from water intrusion

Causes intermittent communication issues

Eventually leads to complete failure

Gel-filled wire nuts alone are insufficient. Use proper DBry6 waterproof splices.

Should I break loops before troubleshooting?

Yes, highly recommended. Loops make "upstream vs. downstream" ambiguous. Breaking loops at the furthest points converts the system to a star/branched pattern with clear directional flow. This makes binary search troubleshooting much more logical and efficient.

What does it mean if I only have overcurrent when a zone operates?

The problem is on the solenoid side of the decoder, not the two-wire path. When the zone is idle, the solenoid circuit isn't active. When the zone operates, a short in the solenoid, solenoid wiring, or decoder-to-solenoid splices causes overcurrent.

Check:

Solenoid resistance (should be 20-60 ohms)

Splices between decoder and solenoid

Wire condition between decoder and valve

Decoder solenoid output connections

What's the difference between a short and a ground fault?

Short Circuit:

Direct or indirect contact between the two wires

Both wires show high current

Current path: Wire 1 → Short → Wire 2 → Back to controller

Ground Fault:

One or both wires making contact with ground/earth

May show high current on only one wire

Current path: Wire → Ground → Earth → Controller ground

Can be intermittent based on soil moisture

Why would readings change between wet and dry weather?

Moisture affects conductivity:

Wet conditions: Ground can conduct electricity, turning opens into ground faults

Dry conditions: Ground doesn't conduct well, ground faults may not show up

Damaged wire/poor splice: Acts as open when dry, short/ground fault when wet

If problems only appear after rain, inspect splices and wire insulation in affected areas.

How do I locate a ground fault between valve boxes?

Use the P-203 Ground Fault Locator:

Isolate the cable section (disconnect from decoders and controller)

Clip transmitter leads to BOTH wires (ensures detection regardless of which wire is faulted)

Walk the wire path with receiver

Locate the point of strongest signal (fault location)

Excavate and repair

Important: Must know approximate wire path route for this method to work efficiently.

Can I use the clamp meter on systems without two-way communication?

Yes, but with limitations. Systems that only have voltage during zone operation (no idle current) cannot be measured when idle. You must:

Put controller in wire test mode if available

Create external power supply to provide steady test current

Or measure during zone operation (readings will be higher)

What if I'm getting inconsistent readings?

Possible causes:

Communication bursts: Engage Low Pass Filter (hold HOLD button 2 seconds)

Not waiting long enough: Wait 2-3 seconds for reading to stabilize

Clamping both wires: Ensure clamping only one wire

Intermittent connection: Problem comes and goes (moisture-related)

Zone operating during measurement: Ensure system is idle (unless intentionally testing during operation)

What resistance should I see on a healthy two-wire path?

Between the two wires: Very high resistance

Should read >600kΩ (or "OL" for overload on most meters)

Low resistance indicates short

Between each wire and ground: Very high resistance

Should read >600kΩ (or "OL")

Low resistance indicates ground fault

With wires shorted at far end:

14-gauge: 2.5 ohms × 2 × (distance in 1000's of feet)

12-gauge: 1.6 ohms × 2 × (distance in 1000's of feet)

Much higher indicates bad splice/corrosion

Why does binary search work better than checking each valve box?

Linear search (check each box):

10 valve boxes = average 5 measurements to find problem

50 valve boxes = average 25 measurements

Binary search (halve each time):

10 valve boxes = maximum 4 measurements

50 valve boxes = maximum 6 measurements

100 valve boxes = maximum 7 measurements

Binary search is logarithmic (log₂), dramatically reducing measurements needed. Each measurement cuts the problem area in half.

How accurate do my measurements need to be?

You're looking for significant differences, not precise numbers:

Expected: 25mA, Reading: 80mA → Clear problem

Expected: 12.5mA, Reading: 12.3mA → Within normal range

Expected: 5mA, Reading: 72mA → Clear problem

Small variations (±10-20%) are normal due to:

Temperature affecting decoder operation

Communication activity

Voltage fluctuations

Manufacturing tolerances

Large variations indicate problems requiring investigation.

What if multiple wire paths have problems?

Troubleshoot one path at a time:

Disconnect all wire paths from controller

Reconnect one path, verify it's healthy (or identify as problem path)

Disconnect that path, reconnect next path

Repeat until all healthy paths identified

Fix each problem path individually before reconnecting

Don't troubleshoot multiple paths simultaneously - too confusing and time-consuming.

Can lightning damage affect my readings?

Yes. Lightning can:

Destroy multiple decoders (especially without proper grounding)

Create shorts in decoders

Damage wire insulation

Affect all decoders on ungrounded path section

If lightning damage suspected:

Check grounding system first

May need to replace multiple decoders

Inspect all splices in affected section

Verify surge arrestors are functioning

What should I do if I find a bad decoder?

Verify it's the decoder: Clamp around wire to that specific decoder (should be low current, if high = decoder problem)

Disconnect decoder from two-wire path

Remeasure: Confirm overcurrent is gone

Test removed decoder: Connect to controller directly to confirm failure

Inspect splices: Bad decoder often indicates poor splices that allowed water in

Replace splices: Use new DBry6 waterproof splices

Install new decoder: Ensure proper splice installation

Test system: Verify normal operation and current readings

How do I know if a splice is bad without breaking it open?

Indirect indicators:

Overcurrent on wire path

Decoder failure

Corrosion visible on splice exterior

Splice feels loose or spongy

Moisture around splice

Intermittent zone operation

Communication errors at that zone

Cannot definitively test without opening, but if decoder failed or overcurrent exists, inspect all splices at that location.

What's the difference between wire test mode and short finding mode?

Terms vary by manufacturer, but generally:

Short Finding Mode / Wire Test Mode:

Provides limited, safe current despite overcurrent condition

Allows troubleshooting without risking equipment

May display current measurements

Some controllers automatically enter this mode

Others require manual activation

Not all controllers have this feature. Older or simpler controllers may just shut down on overcurrent.

Why do I need to isolate both ends when using a ground fault locator?

Safety and accuracy:

Prevents damage: Transmitter voltage could damage decoders

Prevents false readings: Current could flow through decoder internals instead of fault

Safety: Ensures current only flows through the fault you're trying to locate

Accuracy: Eliminates other current paths that could confuse the locator

Always disconnect from controller and any decoders on the section being tested.

Can I use this troubleshooting method on other brands of two-wire systems?

Yes, the principles apply to all two-wire irrigation systems:

Rain Bird (ICI, TBOS, Maxi-Com)

Hunter (ICD, ACC, ICC)

Toro (Sentinel, Lynx)

Weathermatic

And others

However:

Decoder current draw varies by manufacturer

Waveforms differ between systems

Splice requirements may differ

Controller features vary

Always consult manufacturer specifications

The CMA-360B milliamp clamp meter works with all systems due to True RMS and Low Pass Filter capabilities.

What if I'm still getting errors after fixing the overcurrent?

Possible issues:

Additional problems exist: Fix first problem may reveal second problem

Introduced new problem: New splice may be faulty

Communication issue: Path integrity problems (not overcurrent)

Controller problem: May need reset or has separate issue

Wrong decoder replaced: Verify you fixed correct location

Action:

Take new baseline measurement at controller

Repeat troubleshooting process

Verify all splices are properly installed

Check controller diagnostics for new information

How often should I check my two-wire system?

Preventive maintenance schedule:

Monthly (during active season):

Review controller error logs

Check for new error messages

Test random zones for proper operation

Quarterly:

Document baseline current readings

Inspect accessible splices for corrosion

Test grounding system

Annually:

Complete system test (all zones)

Measure current at all major branch points

Inspect valve boxes for moisture/damage

Check all grounding connections

Update system documentation

After storms:

Check system immediately after lightning

Verify grounding system intact

Test for new errors

Proactive monitoring prevents small problems from becoming system failures.

Locating Tools Reference

CMA-360B Milliamp Clamp Meter

Used for:

Measuring current on two-wire path

Finding overcurrent problems

Locating shorts and ground faults

Voltage testing

Resistance testing

Verifying decoder current draw

When to use: Primary tool for all two-wire troubleshooting

P-203 Ground Fault Locator

Used for:

Finding exact location of ground fault between valve boxes

Locating wire damage in turf areas

Pinpointing shorts in buried cable

When to use: After milliamp clamp narrows problem to between two valve boxes

Requirements:

Know approximate wire path route

Must isolate cable section (disconnect both ends)

Clip transmitter to BOTH wires

Wire/Cable Locator (Standard)

Used for:

Tracing wire path route

Finding valve boxes

Mapping system layout

Verifying wire path direction

When to use:

Before troubleshooting (map system)

Finding unmarked valve boxes

Verifying wire path routing

Setup for two-wire:

Black lead to ground stake

Red lead clipped to BOTH wires (for best signal)

Do NOT clip leads to individual wires separately (can damage decoders)

Multimeter / VOM

Used for:

Voltage testing (power supply, transformer output)

Resistance testing (solenoids, wire continuity, shorts)

Solenoid testing

When to use:

Checking controller power

Testing solenoids (20-60 ohms expected)

Wire continuity tests

Supplement to clamp meter

Note: Cannot replace milliamp clamp meter for current measurements (lacks sensitivity).

Troubleshooting Flowchart

Controller turning on?
├─ NO → Check power supply
│        ├─ Power switch
│        ├─ Fuses
│        ├─ Transformer voltage
│        └─ Connections
│        ↓
│        Fixed? → YES → END
│        ↓ NO
│        Disconnect all wire paths
│        ↓
│        Controller works now?
│        ├─ YES → Overcurrent on wire path → Go to OVERCURRENT
│        └─ NO → Controller problem → Contact manufacturer
│
└─ YES → Review controller errors
        ↓
        What does controller show?
        ├─ Overcurrent error → Go to OVERCURRENT
        ├─ Specific zones offline → Go to OPEN CIRCUIT
        ├─ Zone error during operation → Go to SOLENOID SIDE
        └─ Communication errors → Go to COMMUNICATION

OVERCURRENT:
1. Break any loops in system
2. Disconnect wire paths one by one
3. Identify problem wire path
4. Measure current at controller (both wires)
  ├─ High on both wires → SHORT CIRCUIT
  └─ High on one wire → GROUND FAULT
5. Use binary search to locate problem
6. Inspect valve box at problem location
7. Test decoder with clamp meter
8. Replace failed component
9. Verify fix with new measurements

OPEN CIRCUIT:
1. Note which zones are offline
2. Calculate expected vs. actual current
3. Navigate to affected zone area
4. Measure current before first offline zone
5. Measure current at first offline zone
6. Find break point (current drops to zero)
7. Inspect connection at break point
8. Repair/replace connection
9. Verify all zones operational

SOLENOID SIDE:
1. Confirm error only during zone operation
2. Measure solenoid resistance (20-60 ohms)
3. Inspect decoder-to-solenoid splices
4. Check decoder solenoid outputs
5. Replace failed component
6. Test zone operation

COMMUNICATION:
1. Check for overcurrent first (can cause communication errors)
2. Inspect splices at problem decoder
3. Verify decoder not damaged
4. Check wire path continuity
5. Test with known good decoder
6. Replace splices with new DBRY6

END

Best Practices Summary

Installation

Use only specified two-wire cable (double-insulated, solid copper core)

Different colors for different wire paths

Use DBry6 waterproof splices exclusively

Don't nick wire insulation during stripping

Don't overtighten wire twists in splices

Ensure waterproof gel properly positioned in splice

Install grounding at recommended intervals

Install surge arrestors with each ground

Document system layout and decoder locations

Record baseline current measurements

Troubleshooting

Start at controller, gather all available information

Break loops before measuring

Always check both wires

Use binary search for efficiency

Clamp only one wire at a time

Wait 2-3 seconds for stable readings

Engage Low Pass Filter on communicating systems

Measure at branch junctions to isolate problems

Verify fix with new measurements

Document findings for future reference

Maintenance

Proactive monitoring prevents failures

Address intermittent errors immediately

Replace splices when opening valve boxes

Keep system documentation current

Train staff on proper splicing techniques

Inspect after lightning storms

Regular current measurements detect developing problems

Keep spare decoders, splices, and solenoids on hand

Invest in proper tools (milliamp clamp meter, locators)

Learn manufacturer-specific system characteristics

Safety

Never connect transformer directly to short without current limiter

Always use solenoid in test power supply

Isolate sections when using ground fault locator

Power down controller before disconnecting display ribbon

Verify grounding system integrity

Don't exceed transformer ratings

Use proper PPE when working in valve boxes

Follow electrical safety practices

Be aware of other utilities when excavating

Contact manufacturer support when uncertain

Additional Resources

Recommended Training

Noe Cruz YouTube channel: Advanced splicing techniques

Manufacturer-specific training programs

Irrigation Association certification courses

Local distributor technical workshops

Tempo Communications Resources

Product website: Complete CMA-360B specifications

YouTube channel: Tool demonstrations and tutorials

Webinar archives: Past troubleshooting sessions

Technical support: Product-specific questions

Documentation Tools

System mapping software

Current measurement logging templates

Maintenance schedule templates

Troubleshooting checklists

Glossary

Binary Search: Troubleshooting method that divides problem area in half with each measurement

Clamp Meter: Tool that measures current without breaking circuit connections

DBry6: Direct-bury waterproof splice connector for two-wire systems

Decoder: Device that receives signals from controller and operates valves

Ground Fault: Electrical connection between wire and earth/ground

Idle Current: Current consumed by decoder when not operating a zone

Low Pass Filter (LPF): Filter that removes high-frequency signals from measurements

Milliamp (mA): One-thousandth of an amp (0.001 amp)

Ohm's Law: V = I × R (Voltage = Current × Resistance)

Open Circuit: Break in electrical path preventing current flow

Overcurrent: Current draw higher than normal, indicating short or ground fault

Short Circuit: Unintended low-resistance connection between two wires

Solenoid: Electromagnetic coil that opens/closes irrigation valve

True RMS: Measurement method accurate for any waveform shape

Two-Way Communication: Bidirectional data exchange between controller and decoders

Two-Wire Path: Complete circuit of two wires connecting controller to decoders

Upstream/Downstream: Direction relative to current flow from controller

Wire Test Mode: Controller mode providing safe current for troubleshooting

Document Information

Title: Two-Wire System Troubleshooting with Milliamp Clamp Meter - Customer Support Guide

Version: 1.0

Last Updated: Based on Tempo Communications webinar content

Presenter: Alejandro Asencio, Associate Product Manager - Irrigation

Primary Tool: Tempo CMA-360B Milliamp Clamp Meter

Intended Audience: Customer support teams, field technicians, irrigation professionals

Prerequisites: Basic understanding of electricity, irrigation systems, and multimeter use

Related Documents:

CMA-360B Product Manual

P-203 Ground Fault Locator Guide

Manufacturer-specific two-wire system documentation

If you have reviewed all of the above information and have not resolved the issue, consider contacting Hydropoint Support. Hydropoint Support can be reached at support@baselinesystems.com, support@hydropoint.com or 866-294-5847.